Form-Fill-Seal system CONTINUA

This machine is designed for very high throughputs until 1800 b/h, depending on the characteristics of the product.
It has three operating stations: one to form the bottom of the bag and cut the film to the desired length, the second one for filling and the third one for sealing the upper bag edge.

The Concetti Group has studied special technical solutions in terms of both mechanics and electronics, allowing the machine to achieve the high speeds that are required.

The operating phases and the changeover of the machine operating parameters are PLC-assisted and can be completed in a very short amount of time, without any operator intervention, thanks to the actuators mounted on the machine. The monobloc structure, equipped with inspection doors, makes the system perfectly safe for the
operator.

CONTINUA FFS – Tubular form Fill Seal Machine
CONTINUA FFS – Tubular form Fill Seal Machine

CONTINUA FFS – Tubular form Fill Seal Machine
FFS CONTINUA 600
form fill seal CONTINUA with belt fed weigher
Insaccatrice da bobina tubolare con palettizzatore dall alto


Technical Data

Max. productions 600s/h
Reel Ø max 1500 mm
Bag weight From 10 to 50 kg
Bag length min 320 max 420 mm
min 280 with a special bag-holder
Gusset depth min 40 max 90 mm
Film thickness 80-250 µm
Power supply 380 V- 50 Hz
Installed power 13 kW
Compressed-air consumption 100 Nl/cycle
 Standard degree of protection IP 55
Self-diagnostic system   
Soundproofing  
Contact parts in stainless steel  


OPTIONS

  • Servo-assisted reel-change system.
  • Micro-perforation device for the tubular film in order to eliminate air from the inside of the bag
  • Printing of alphanumeric characters on one or both sides of the tubular film.
  • 45-degree seal for bottom corners and tops of gusseted bags.
  • Probe deaerationunit to minimize the volume of fluidized products.
  • Probe device to eliminate air between the product and the sealed mouth of the bag.
  • Device to add inert gas to the bag before the bag mouth is closed. 
  • Device to clean the upper bag edges when working with dusty products.
  • Possibility of handling reels with a preformed handle.
  • Painting of the structure with a cycle to meet the needs imposed by the products to be handled.
  • Construction of the entire machine in stainless steel.
  • Base for moving the machine (in manual or motorized), in order to use it with several outlets (silos) and work with products that have different characteristics.
  • Device to reopen and clean the upper bag edges for products that could impede sealing.
  • Gusseting device to make a gusseted bag from flat tubular film.
  • IP 65 protection
  • Dust-proofing cushions on the bag-holder.
  • Device for sealing a strip over the bag mouth.
  • Possibility of making the handle during the bag-forming phase.  


NOTE: The information listed in the chart is strictly indicative and will depend on the specific features of each machine.

Max. productions 900s/h
Reel Ø max 1500 mm
Bag weight From 10 to 50 kg
Bag length min 550 max 1000 mm
Bag width min 320 max 420 mm
min 280 con with a special bag-holder
Gusset depth min 40 max 90 mm
Film thickness 80-250 µm
Power supply 380 V- 50 Hz
Installed power 16 kW
Compressed-air consumption 80 Nl/cycle
 Standard degree of protection IP 55
Self-diagnostic system   
Soundproofing  
Contact parts in stainless steel nbsp;

OPTIONS

  • Servo-assisted reel-change system.
  • Micro-perforation device for the tubular film in order to eliminate air from the inside of the bag
  • Printing of alphanumeric characters on one or both sides of the tubular film.
  • 45-degree seal for bottom corners and tops of gusseted bags.
  • Probe deaerationunit to minimize the volume of fluidized products.
  • Probe device to eliminate air between the product and the sealed mouth of the bag.
  • Device to add inert gas to the bag before the bag mouth is closed. 
  • Device to clean the upper bag edges when working with dusty products.
  • Possibility of handling reels with a preformed handle.
  • Painting of the structure with a cycle to meet the needs imposed by the products to be handled.
  • Construction of the entire machine in stainless steel.
  • Base for moving the machine (in manual or motorized), in order to use it with several outlets (silos) and work with products that have different characteristics.
  • Device to reopen and clean the upper bag edges for products that could impede sealing.
  • Gusseting device to make a gusseted bag from flat tubular film.
  • IP 65 protection
  • Dust-proofing cushions on the bag-holder.
  • Device for sealing a strip over the bag mouth.
  • Possibility of making the handle during the bag-forming phase.  


NOTE: The information listed in the chart is strictly indicative and will depend on the specific features of each machine.

Max. productions 1200s/h
Reel Ø max 1500 mm
Bag weight From 10 to 50 kg
Bag length min 550 max 1000 mm
Bag width min 320 max 420 mm
min 280 con with a special bag-holder
Gusset depth min 40 max 90 mm
Film thickness 80-250 µm
Power supply 380 V- 50 Hz
Installed power 18 kW
Compressed-air consumption 110 Nl/cycle
 Standard degree of protection IP 55
Self-diagnostic system   
Soundproofing  
Contact parts in stainless steel  

OPTIONS

  • Servo-assisted reel-change system.
  • Micro-perforation device for the tubular film in order to eliminate air from the inside of the bag.
  • Printing of alphanumeric characters on one or both sides of the tubular film.
  • 45-degree seal for bottom corners and tops of gusseted bags.
  • Probe deaerationunit to minimize the volume of fluidized products.
  • Probe device to eliminate air between the product and the sealed mouth of the bag.
  • Device to add inert gas to the bag before the bag mouth is closed. 
  • Device to clean the upper bag edges when working with dusty products.
  • Possibility of handling reels with a preformed handle.
  • Painting of the structure with a cycle to meet the needs imposed by the products to be handled.
  • Construction of the entire machine in stainless steel.
  • Base for moving the machine (in manual or motorized), in order to use it with several outlets (silos) and work with products that have different characteristics.
  • Device to reopen and clean the upper bag edges for products that could impede sealing.
  • Gusseting device to make a gusseted bag from flat tubular film.
  • IP 65 protection
  • Dust-proofing cushions on the bag-holder.
  • Device for sealing a strip over the bag mouth.
  • Possibility of making the handle during the bag-forming phase.  


NOTE: The information listed in the chart is strictly indicative and will depend on the specific features of each machine.

Max. productions 1600s/h
Reel Ø max 1500 mm
Bag weight From 10 to 50 kg
Bag length min 550 max 1000 mm
Bag width min 320 max 420 mm
min 280 con with a special bag-holder
Gusset depth min 40 max 90 mm
Film thickness 80-250 µm
Power supply 380 V- 50 Hz
Installed power 18 kW
Compressed-air consumption 110 Nl/cycle
 Standard degree of protection IP 55
Self-diagnostic system   
Soundproofing  
Contact parts in stainless steel  

OPTIONS

  • Servo-assisted reel-change system.
  • Micro-perforation device for the tubular film in order to eliminate air from the inside of the bag
  • Printing of alphanumeric characters on one or both sides of the tubular film.
  • 45-degree seal for bottom corners and tops of gusseted bags.
  • Probe deaerationunit to minimize the volume of fluidized products.
  • Probe device to eliminate air between the product and the sealed mouth of the bag.
  • Device to add inert gas to the bag before the bag mouth is closed. 
  • Device to clean the upper bag edges when working with dusty products.
  • Possibility of handling reels with a preformed handle.
  • Painting of the structure with a cycle to meet the needs imposed by the products to be handled.
  • Construction of the entire machine in stainless steel.
  • Base for moving the machine (in manual or motorized), in order to use it with several outlets (silos) and work with products that have different characteristics.
  • Device to reopen and clean the upper bag edges for products that could impede sealing.
  • Gusseting device to make a gusseted bag from flat tubular film.
  • IP 65 protection
  • Dust-proofing cushions on the bag-holder.
  • Device for sealing a strip over the bag mouth.
  • Possibility of making the handle during the bag-forming phase.  


NOTE: The information listed in the chart is strictly indicative and will depend on the specific features of each machine.

Max. productions 1800s/h
Reel Ø max 1500 mm
Bag weight From 4 to 50 kg
Bag length min 550 max 1000 mm
Bag width min 320 max 420 mm
min 280 con with a special bag-holder
Gusset depth min 40 max 90 mm
Film thickness 80-250 µm
Power supply 380 V- 50 Hz
Installed power 18 kW
Compressed-air consumption 110 Nl/cycle
Standard degree of protection IP 55
Self-diagnostic system  
Soundproofing  
Contact parts in stainless steel  

OPTIONS

  • Servo-assisted reel-change system.
  • Micro-perforation device for the tubular film in order to eliminate air from the inside of the bag
  • Printing of alphanumeric characters on one or both sides of the tubular film.
  • 45-degree seal for bottom corners and tops of gusseted bags.
  • Probe deaerationunit to minimize the volume of fluidized products.
  • Probe device to eliminate air between the product and the sealed mouth of the bag.
  • Device to add inert gas to the bag before the bag mouth is closed. 
  • Device to clean the upper bag edges when working with dusty products.
  • Possibility of handling reels with a preformed handle.
  • Painting of the structure with a cycle to meet the needs imposed by the products to be handled.
  • Construction of the entire machine in stainless steel.
  • Base for moving the machine (in manual or motorized), in order to use it with several outlets (silos) and work with products that have different characteristics.
  • Device to reopen and clean the upper bag edges for products that could impede sealing.
  • Gusseting device to make a gusseted bag from flat tubular film.
  • IP 65 protection
  • Dust-proofing cushions on the bag-holder.
  • Device for sealing a strip over the bag mouth.
  • Possibility of making the handle during the bag-forming phase. 


NOTE: The information listed in the chart is strictly indicative and will depend on the specific features of each machine.

PackExpo2016Las Vegas, Nevada (IL-USA)
September 25-27, 2017
Ippe 2017 Atlanta (GA-USA) 
January 30 - February 1, 2018
 

Concetti Group Worldwide

The Concetti Group is present in over 46 countries with a network of qualified agents who can offer customers the assistance they need for studying appropriate production solutions, technical support, personnel training and the supply of spare parts.

 

mappa


This website uses cookies, including third-parties cookies, necessary for the website operation and useful for the purposes described in the Cookie policy.
By closing this banner, scrolling this page, clicking on a link or continuing the navigation in any other way, you consent to the use of cookies.